Changing aluminium windows with vinyl retrofit windows or replacement style windows

In previous posts, I discussed to you how to identify whether your windows are prospects for vinyl replacement style frames or retrofit design frames. This week I’m going to explain the installation techniques for both frame styles. Let’s begin with the retrofit frame.

Retrofit window setup is truly the most convenient of all. The retrofit window already includes an exterior trim attached. That’s the flush fin that goes against the outdoors surface area, typically stucco. Prepare the window by drilling 3/8″ holes in the locations of the frame where you wish to screw it in place. Generally, there will be 3 holes on each side and 3 more across the top. Don’t pre-drill any holes in the bottom track. After eliminating the old panels, you wish to run a heavy bead of caulk on the face of the old aluminium frame that you left in place. Then you and a helper set the bottom of the vinyl window onto the old aluminium bottom track and raise it into position. The flush fin or retrofit lip will serve as a “stop” to hold the window in place. Have your assistant hold the window while you go within.

When inside, you want to focus the window in the opening. Move the vent panel open and closed to make sure the window is plumb and level. To change for out of square conditions, shim the bottom right or left corner by positioning a shimming product in between the sill and bottom of the window frame. As soon as square, drive a 3″ deck screw through the 3/8″ holes and into the wood studs.Just seat the screw, do not over-tighten. After you get the screws into the sides and top, remove the moving panel. The bottom track ought to lift out. Try to find drain holes in the track and insert a thin screwdriver and raise. Drive one screw in the bottom centre. caulk around the screw head, then put the track back in place and re-install the sliding panel. Now, you want to go back outside and caulk the gap where the retrofit fin satisfies the exterior surface of your house. You wish to have a double barrier of security versus water infiltration. Keep in mind, you currently applied a generous bead of caulk prior to inserting the new frame into the opening. The rest of the task is done on the within.

You want to plug the 3/8″ screw holes to hide the heads of the screws. The plugs will pop into location in the hole. The next step is to fill the space around the brand-new frame with R-13 Insulation. Do not use the foam insulation that comes in a can. Many makers will not honour the service warranty if the foam is used. Even the non broadening foams can trigger the frame to distort, triggering problems. Pack the insulation in tight. You might wish to use a dust mask throughout this procedure. Many individuals, myself consisted of, are really conscious insulation. After the insulation remains in place, you want to install trim around the inside to complete the task. You can use wood trim from the hardware shop, or some other product. In my experience, the finest product is a vinyl flat trim that matches the window frame. Ours is available in 2 various widths, although the 1 3/4″ wide piece is by far the most typical. The trim has a double sided adhesive tape on the back. You cut the leading and bottom initially, stick them on the vinyl frame, making sure the trim goes to the drywall. This covers all the insulation and the old metal frame. Do the side pieces next. The final action is to caulk where the trim satisfies the walls.

Much of the installation procedure for a replacement frame is the same as the retrofit frame. But, there are a couple of differences. When you put the new window into the opening using a replacement frame, you don’t have the flush fin holding the frame in place. You and your assistant need to hold the frame in place while you put a screw in the leading centre to support the frame. You can do your adjusting for a square condition. All of the treatments on the inside will be precisely the exact same, from hole plugs, to insulation, to trim and caulk. The outside is different. You have to use the trim that belonged to the retrofit frame. Once again, I choose the flat trim. Once again, you use a bead of caulk to the old frame, then determine and cut the leading and bottom trim pieces. Use the adhesive part of the trim to the vinyl frame, and let the other part get in touch with the bead of caulk. Trim all four sides, then caulk again where the trim satisfies the outside product.

Post Sponsored by Liverpool Glass 24/7 – Local Emergency Glazier.

Leave a Reply

Your email address will not be published. Required fields are marked *